13:22. Central blocking
Prevention
Before work on system of the central blocking to remove a weight wire from the accumulator and to connect the accumulator after completion of works.
ELECTRONIC CONTROL DEVICE
Removal
| PERFORMANCE ORDER |
|
1. To remove a ware box for access to the control unit (the arrow specified the central block of the electronic control device of blocking on models till 1992). |
|
2. To unscrew two screws of fastening, to remove the control unit and to disconnect the electric socket from the block. |
|
Installation
Installation is made in the sequence, the return to removal.
ENGINE OF THE DRIVE OF THE DOOR LOCK
Engines are installed on the door lock.
| PERFORMANCE ORDER |
| To remove the engine, it is necessary to remove the lock, then to unscrew the screws fixing the engine to the lock. |
|
ENGINE OF THE LOCK OF THE BACK DOOR
Removal
| PERFORMANCE ORDER |
| 1. To open a back door. |
| 2. To unscrew screws of fastening and to remove plastic finishing from an internal part of a back door. |
| 3. Working around edge of carpet finishing, to release brackets of fastening and to remove carpet finishing. |
|
4. To unscrew a bolt, the fixing lock engine to a back door. |
|
5. To take the lock drive engine from an opening in a back door, then to disconnect draft of the lock and the electric socket. |
|
Installation
Installation is made in the sequence, the return to removal.
TRUNK LID LOCK ENGINE
Removal
| PERFORMANCE ORDER |
| 1. To open a trunk lid. |
| 2. To take percussion caps of fastening of an upholstery of a luggage carrier and to turn off finishing of a luggage carrier from the upper edge of the luggage compartment. |
| 3. To unscrew fastening screws, to remove the engine of the lock and to disconnect a lath. |
| 4. To disconnect the electric socket from the engine and to remove the engine. |
|
Installation
Installation is made in the sequence, the return to removal.
FOLDING SHUTTER OF THE FILLER OF THE FUEL TANK (MODEL SEDAN)
On the Sedan models the engine of opening of a folding shutter of a filler of the fuel tank is located in the luggage compartment, behind a back part of the right side finishing.
Removal
| PERFORMANCE ORDER |
| 1. By means of the lever to remove the right side carpet finishing in the luggage compartment for access to the lock engine. |
| 2. To open a folding shutter of a filler of the fuel tank and to unscrew a bolt, the fixing engine to a body. |
| 3. Working in the luggage compartment, to unscrew a bolt, then to take the engine and to disconnect the electric socket. |
|
Installation
Installation is made in the sequence, the return to removal.
FOLDING SHUTTER OF THE FILLER OF THE FUEL TANK (KOMB MODEL)
On models of Kombi the engine of opening of a folding shutter of a filler of the fuel tank is located in the luggage compartment behind a windscreen washer tank.
Removal
| PERFORMANCE ORDER |
| 1. Working in the luggage compartment, to open a folding shutter for access to a back tank of windscreen washer. |
| 2. To unscrew two screws of fastening, then to lift a windscreen washer tank for access to the lock engine. |
|
|
3. To unscrew a bolt of fastening of the engine of the drive of a folding shutter of a filler of the fuel tank. |
|
4. To take the engine of the drive of a folding shutter of a filler of the fuel tank on models of Kombi and to disconnect the electric socket. |
|
Installation
Installation is made in the sequence, the return to removal.
RECEIVER OF REMOTE CONTROL
The receiver of remote control is located in the ceiling panel.
Removal
| PERFORMANCE ORDER |
| 1. To uncover the ceiling panel. |
| 2. To remove the illumination lamp switch from the panel for access to two screws. To disconnect the socket and to remove the illumination lamp switch. |
| 3. To remove an illumination lamp plafond from the panel for access to the screw. To disconnect the socket and to remove an illumination lamp. |
| 4. By means of the lever to remove the locking plate from the panel, and also to remove the hatch switch from the panel. |
|
5. To unscrew two screws of fastening of the panel, then to lower the panel from a ceiling. |
|
6. To release brackets (are specified by shooters) and to remove the receiver from the panel. |
|
Installation
Installation is made in the sequence, the return to removal.
Replacement of the battery of the transmitter of remote control
EARLY MODELS
| PERFORMANCE ORDER |
|
1. Using the small screw-driver, to remove a back cover from the case of the transmitter and to take three batteries (are specified by shooters), noting situation in which they were established. |
| 2. To install new batteries, observing polarity of connection of batteries. |
| 3. To install a back cover with batteries on the transmitter. |
|
LATE MODELS
| PERFORMANCE ORDER |
| 1. To unscrew screws of fastening of two half of the case of the transmitter. |
| 2. To take two batteries, noting situation in which they were installed. |
| 3. To install new batteries, observing polarity of connection of batteries. |
| 4. To connect two half of the case of the transmitter and to screw up fastening screws. |
|
