13.1. Care of a body
Check of a condition of a body has to be made regularly. Otherwise corrosion of certain sites of a body can lead to its strong damage and, further, expensive repair. It is also important to pay attention to parts of the car inaccessible to an external look, for example, to the bottom, arches of wheels and the lower part of a motor compartment, and also the parts of a body hidden under an upholstery.
Basic element at care of a body is its sink. Before a wash of the car soak insects and remove from a body surface. Plentifully use water. Use a soft sponge or a soft brush. The varnish covering cannot be washed with a stream with a strong pressure. Pour over the car from a hose and wash away dirt from top to down. Often rinse a sponge. Wipe the car with pure rags. Apply only the good degreasing washing substances. For the purpose of protection for a sink add the washing preservatives to water. It is forbidden to wash and dry the car in the sun, otherwise on a varnish surface there will be spots. Salt with which roads strew makes harmful effects on a car body.
Purely washed up and dried up varnish covering needs to be processed every 3 month the preserving means to protect the surface of the car from atmospheric influences by creation of a pore-free water-repellent wax layer.
At once to remove the flowed-out fuel, oil or lubricant, and also brake fluid, otherwise color of a varnish covering will change.
Processing of a surface needs to be repeated if water does not gather in drops, and spreads on a surface. Regular processing by the preserving means promotes long preservation of gloss of a varnish covering.
There is also other possibility of protection of varnish coverings – by means of the washing preservatives. However the washing preservatives provide reliable protection of varnish coverings only in case are used at each wash of the car and at least, than in 2–3 weeks.
After use of the washing (foam-forming) means additional processing of a surface by preservatives especially is recommended.
Polishing of a varnish surface is necessary only in case it faded owing to insufficient leaving, influence of dust, harmful gases, weather conditions, and the preserving means cannot restore its gloss.
It is not necessary to apply rough polishing pastes and chemically active polishing means (despite previously good results).
Before polishing the car needs to be washed up and to dry up carefully. To further adhere to the instruction for use of the polishing means.
To make polishing small sites in order to avoid premature drying of polish. After processing of a surface some polishing means it is necessary to make additional preservation. It is forbidden to polish in the open sun. Opaque varnish surfaces cannot be processed the preserving and polishing means.
Removal of spots of pitch
Pitch quickly diffundirut in varnish coverings and it is impossible to remove it completely already. Fresh spots of pitch can be removed with the soft rag moistened in flushing gasoline. In case of emergency it is possible to use usual gasoline, kerosene or turpentine. Pitch spots well are removed by means of varnish preservatives. In this case the wash of the car is not required.
Removal of insects
Insects contain substances which can damage a varnish film if quickly not to remove them. Insects can be washed away only weak, slightly warm soap or washing solution or by means of special means for removal of insects.
Removal of construction solutions
Splashes of construction materials are washed away by slightly warm solution of neutral detergents. Not to rub strongly, otherwise it is possible to scratch a varnish covering. Then carefully to rinse with clear water.
Sink of glasses
To wipe glasses with a pure soft rag from the internal and outer side. At strong pollution it is possible to use alcohol or liquid ammonia and warm water, and also special means for purification of glasses. At a windshield sink to lift screen wipers up.
Care of rubber consolidations
Periodically to strew the condensing or sliding surfaces with talc or to spray silicone аэрозолью. It will keep their elasticity and will exclude a scratch when closing doors. It is possible to eliminate unpleasant sounds, having wiped the adjoining surfaces with liquid soap.
Care of disks of wheels
Disks of wheels from light metals demand leaving, especially in cold season. For this purpose it is possible to use special means for cleaning of disks. Not to apply active, acidiferous, silnoshchelochny and rough cleaners or water with a temperature over +60 °C.
Care of seat belts
Seat belts should be washed with weak alkaline solution, without removing them. Not to subject them to dry cleaning which can cause destruction of fibers. To twist belts with automatic winding in the dried-up state, if necessary to use special an aerosol (for the best sliding). It is not recommended to dry belts at a temperature over 80 °C and in the open sun.